Thursday, December 22, 2011

How to Fix Error Code 5100 on a Canon MX700

(adsbygoogle = window.adsbygoogle || []).push({}); The Canon Pixma MX700 multifunction printer includes an LCD display that shows various error codes whenever a hardware or software problem occurs. Each error code is tied to a specific type of issue to make the troubleshooting process easier. Error code 5100 describes a physical problem either with a paper jam or an incorrectly seated ink tank. Resolving the error is a quick process that only requires a few standard troubleshooting procedures. Instructions 1) Press down and hold the "On/Off"...

Monday, December 19, 2011

Fix Printer Error 49

Printer Error 49 usually appears when you are attempting to print a document using a HP printer and then a communication failure error occurs between the computer and the printer. However, there are other probable causes for this message with an error 49 code to appear. There is a chance that it is related to the file that is being printed, or it could be due to a firmware problem. You must determine the cause of the problem and then fix the error to be able to make use of your printer again. This tutorial will guide you how to resolve...

Wednesday, December 14, 2011

How to Replace a Fuser on an IBM InfoPrint 40

Follow the instruction to Replace a Fuser on an IBM InfoPrint 40 1) Turn the printer off and then remove the power cord from the electrical outlet. 2) Remove the power cord connection from the back of the printer. 3) Wait 20 minutes for the printer to cool down. If it has not completely cooled, wait an additional 10 minutes and then check it again. Do not proceed unless the printer has cooled down adequately. 4) Push the auxiliary tray, bin feeder or other bin that is attached to the duplex unit up slightly and then pull it out of the...

Troubleshoot an IBM Infoprint 1145

Follow the instruction to fix the issue in IBM printer 1) Check that you connected your printer to the power outlet correctly. The plug that goes into the wall or extension cord must go in all the way down to the rubber end of the plug. 2) Verify the USB connection between your printer and the computer if you have your printer connected to a computer. Try other USB ports on your computer to make sure that your problem doesn’t come from a fault in the computer’s USB port itself. 3) Disassemble your printer's exterior while consulting your...

Monday, December 12, 2011

Konica Minolta Magicolor 2530DL Troubleshooting

Konica Minolta released the Magicolor 2530 DL printer in the summer of 2006. This printer is designed for small offices or home offices, with a maximum output of 20 pages per minute in black and white and five pages per minute in color. The maximum resolution is 2400 dots per inch by 600 dots per inch. This printer is no longer available for sale new, but replacement cartridges can still be found. As with all printers, the Magicolor 2530 is prone to occasional issues, but Konica Minolta provides helpful troubleshooting tips. Misfeeds 1) Make...

Enable Duplex Printing on the Konica Minolta DI3510F Printer

Multifunction printers like the Konica-Minolta Pi3505f provide print, scan, copy and fax services in a single machine. The Pi3505f multifunction device is also capable of printing duplexed or double-sided pages if an additional attachment is installed. To enable duplex printing on this printer model, you will need to access the printer's setup information through the touch panel located on the front of the printer. Follow the instruction to fix the issue 1) Press "Printer Settings" on the printer's touch panel and select the "Default...

Wednesday, December 7, 2011

How Do MICR Printers Work?

Magnetic Ink Character Recognition, or popularly known as MICR, is a standardized printing and character recognition technology primarily used by the banking industry. The technology allows for the speedy processing of bank cheques and for other printing purposes that require some level of security. For most people, this technology seems obscure. Nevertheless, recent advancements in MICR printing are making it even more relevant for a more diverse set of functions. The Need for MICR Technology Why is there a need for MICR in the first place?...

Fix Left or Right Cartridge Incorrect in Lexmark Printer

Several months ago I had purchased my Mother-in-law a new Lexmark X9575 as an easy way to provide print, fax and copy functionality in one unit. She isn't the most technically proficient person in the world. So, I wanted to get her something that is easy to use and maintain. The Lexmark 9575 is what is considered a thermal inkjet. This machine produces black prints in up to 1200 x 1200 dpi and color prints up to 4800 x 2400 dpi. It prints 33 pages per minute in black and 28 pages per minute in color. So, this machine has top end specs for...

Tuesday, December 6, 2011

Brother Printer Error Codes

ch_client = "praroopkhare"; ch_width = 250; ch_height = 250; ch_type = "mpu"; ch_sid = "JUSTforEnjoyment"; ch_color_site_link = "0000CC"; ch_color_title = "0000CC"; ch_color_border = "FFFFFF"; ch_color_text = "000000"; ch_color_bg = "FFFFFF"; Have you ever encountered a printer error code while using your Brother multifunction printer? Chances are that you have. It is not that the Brother printer is an inferior machine; in fact, it is one of the best multifunction printers out there. But just like any machine, it can bog down. And when it...

Fix Most Common Brother Printer Problems

Brother Printers supply premium products which are well designed and these come with first rate customer value. Also, this company has been winning a lot of awards for many years now. This is because, no matter what the printing requirements are - whether it is for home or for home office usage, for desktop office utilization, as well as small or the medium sized associated workgroups or it is color, Brother Printers are ready with the printing solutions for all printing needs. Now the question is how to fix the most common Brother Printer...

Monday, December 5, 2011

Steps to Fix Runtime Error 482

How To Fix Runtime Error 482 The Runtime 482 Error arises when the user attempts to utilise the “PrintForm” protocol. More specifically, when the user attempts to change a page level setting (such as Orientation) the Runtime Error 482 is shown due to either a damaged part of your system or a corrupt file causing the damage. This error is typically present on older computers using the operating systems Windows 95, 98, ME, NT, or 2000; and can arise at seemingly random times. Here’s how to fix this error: What Causes Runtime Error 482 The...

HP Printer Error Codes

(adsbygoogle = window.adsbygoogle || []).push({}); Are you worried about the numbers that come out from your printer's display panel while you are using your HP printers? Well, these can be HP printer error codes. You don't have to worry about them as there are solutions to such errors. Want to know more about what these error codes are and see how they can be solved? HP printer error codes to watch out for Some of the most common printer error codes that can pop out your computer screens (or your printer's display panel) are due to paper...

Fix HP Printer Error Code 20

HP Printer error code 20, as the name describes, is a problem with the HP printer on your system. The issue is typically caused if the printer is either not configured correctly, or your system tries to send an erroneous command to it. This error will typically show when you try and print a document / spreadsheet or another piece of data from your system, and will stop the print-out from proceeding. In order to fix this, it's advisable that you follow the steps outlined in this tutorial. The HP error 20 will generally show in this format: There...

Friday, December 2, 2011

Fix Printer Error 0x000006be

Are you trying to connect to print queue hosted on Windows XP, Windows 2000 Server or Windows 2003 Server while your operating system is Windows Vista or Windows 2000 Server client? You may receive Error 0x000006be. (adsbygoogle = window.adsbygoogle || []).push({}); ch_client = "praroopkhare"; ch_width = 250; ch_height = 250; ch_type = "mpu"; ch_sid = "JUSTforEnjoyment"; ch_color_site_link = "0000CC"; ch_color_title = "0000CC"; ch_color_border = "FFFFFF"; ch_color_text = "000000"; ch_color_bg = "FFFFFF"; On client system users are either...

Thursday, December 1, 2011

Fix Error Code 0x000006d9 on a Sharing a Printer in Window 7

This Error comes when you are try to share the printer and the system leaves you with Error Code 0x000006d9. The problem occurs because of two issues: - 1. Window Firewall is Turned On. 2. Network discovery and Printer sharing is Turned Off. So by turning off the Widows Firewall and turning on the network discovery and printer sharing the error code can be fixed. Steps to turn off Windows Firewall: - 1. Left Click Start Menu Button and Type services.msc in the Search Space. Right Click on...

Wednesday, November 30, 2011

HP 940/940XL Warning of Low Ink

If you have just installed a refilled, remanufactured or compatible HP 940 or HP 940XL it is likely that it uses a HP original chip to identify itself to the printer. These chips use a combination of counting pages and average page coverage to estimate the amount of ink inside the cartridge. As they have no way to check the physical ink level in a cartridge, a chip that has been used previously will almost certainly warn of having low ink or even being empty once installed. The message should look...

Fix HP LaserJet Printer Error 56

If you are receiving this message on the: HP LaserJet IID or IIID then duplex has not been selected with the output selector knob on the rear assembly. Move into the correct position and try again. HP LaserJet IIISi or 4Si a print job has been sent to print to envelopes while the printer was in duplex mode. Change mode and then try again. On all other printers: Turn the printer off. Leave for 30 seconds. Turn the printer on again. Check the printer’s configuration. Verify accessory connection. If this does not resolve the problem please...

Tuesday, November 29, 2011

“CHANGE DRUM SOON” message after changing a Brother DR8000

The “CHANGE DRUM SOON” message will appear once your DR8000 drum unit nears the end of its life. We advise continuing to use your current drum unit until you begin to experience print quality problems before installing a new one. If the clear plastic “starter sheet” is removed from the replacement drum before installation this message will continue to show . It is this sheet that actually resets the drum counter. If the sheet has already been removed you can reinstall drum with the starter sheet by following the simple steps below: -Find...

Fix HP LaserJet Error 89

This error will normally be caused by an accessory not being oriented properlyor having broken pins. If you have recently installed a part please double the installation and consult any manuals provided. It can alsobe a simple temporay error so please try the following: Step 1. Turn the printer off. Step 2. Leave for 30 seconds. Step 3. Turn the printer back on. Step 4. Resend the print job if necessary. If the problem remains please contact HP technical support if the machine is in warranty or a technician if the warranty...

Fix Printer ERROR 11 Paper Out

Error code 11 Problem: " Paper out" error message Possible Causes and Solutions: 1. Paper tray empty or not seated correctly. First try to re-seat the paper tray by pulling it out, making sure there are no obstructions in it's path and reinsert it. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. Take a sharp tool, like a razor blade and scrape the buildup off these edges. Also, check for cracks in the cassette. The cassette will loose it's stiffness and keep from holding its shape when...

Monday, November 28, 2011

How to Reset Kyocra Copiers

kyocera machines have a self diagnostic function to displays an error code whenever a problem occurs. Low level error codes can be reset by simply restarting the machine but some of them (C 6000, C 6020, C 6030, C 6050, C 6100, C 6200, C 6300 etc) must be reset by a technician. Causes: 1. Unstable power source 2. Low/High voltages 3. Broken thermisted wire 4. Poor contact in the thermister connector terminals. 5. Heater lamps are broken or not installed correctly. Before reseting "6XXX" series code, make very sure that defective parts have...

Friday, November 25, 2011

Fix Error code 0xC19A003

For any other 'Ink System Failure ' message or other '0x ' error as listed at the top of this document, follow these solutions to resolve the issue. Solution one: Reset the printer The error message might disappear after you turn off the printer and then turn it on again. After you make any adjustments to the cartridges or the printhead, reset the printer in order for the error message to clear completely. Follow these steps to reset the printer. Press the Power button to turn on the product. With...

0xc19a0013 or no code displays with the 'Ink System Failure' error Message

Follow these steps to resolve the issue of 'Ink System Failure ' with an accompanying '0xc19a0013 ' error, or no '0x ' error at all. Solution one: Check the cartridges The ink system can fail if the cartridges in the printer are installed incorrectly, if the ink in the cartridge is low or out, or if the cartridges are damaged or not correctly vented. Follow these steps to check the cartridges thoroughly and resolve any issues you might find. Step one: Replace empty or low cartridges The...

HP k8600 will not print from win7

Following are some of the tips, which you must follow while you are using a printer with Windows 7 system. Ensure that the cables are properly connected; you need to ensure that your printer is properly connected, and plugged in, and also the cable is accurately connected to the computer as well. Check the power; make sure that the printer’s power is switched on, ensure that all the computer necessary computer components are also turned on. Make sure that the hardware is properly plugged in, and also turned on. Apply troubleshooting. A troubleshooter...

Tuesday, November 22, 2011

Fix Code 19 in Printers

Delete the Upper and Lower FiltersStep 1: Go into the registry of your computer. The registry is accessed through the "Start" menu. Type "regedit" into the search box and hit "Enter." Step 2: Find the registry entry that reads "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}." Click on this entry to highlight it. Step 3: Choose "UpperFilters" from the options in the right-hand pane. If an entry appears under "UpperFilters," go to the "Edit" menu and choose "Delete."...

Fix Error code SC542

SC 542 Basically the machine is telling you that the fuser did not reach its target temperature in a specified amount of time. In normal circumstances this code will apear if the thermistor is not maintained or replace periodically or in abnormal circumstance the heat lamp blew. This is a Service Tech reset code. Once the error is detected, the printer is toast until you manually clear the error from the keypad. Even though the printer is physically fine, it won't come ready until the prior error condition is cleared. ch_client = "praroopkhare"; ch_width...

Friday, November 18, 2011

PRINTER SETTINGS IN MAC

Use the print dialog to choose your printer and select options for how you want your document to print. 1. Open the document you want to print. 2. If you wish to change the paper size or page orientation, choose File > Page Setup. 3. Choose File > Print. 4. Select your printer from the Printer pop-up menu. 5. If you wish to change any printer driver settings, select the necessary options in the print dialog. You can select more options from the Copies & Pages menu. 6. Click Pri...

Reseat Fuser Dell 2135cn Printer

Notice: To protect the drums of the print cartridges against bright light, close the front cover within 5 minutes. If the front cover remains open for more than 5 minutes, print quality may deteriorate. Note: Remove any print jobs from the center output tray, and close the multipurpose feeder cover before opening the front cover. To reseat the fuser, perform the following steps: 1. Turn off the printer and wait for 30 minutes. 2. Push the side button and open the front cover 3. Pull the...

Thursday, November 17, 2011

Konica Minolta/Ineo/Develop Error Codes

Konica Minolta Bizhub/ineo/develop machines display an error code when a problem occurs in the machine. It is alway a good practice to call a certified technician to fix the problem. The following information has carefully been collected from various sources without any guarantee. ch_client = "praroopkhare"; ch_width = 250; ch_height = 250; ch_type = "mpu"; ch_sid = "JUSTforEnjoyment"; ch_color_site_link = "0000CC"; ch_color_title = "0000CC"; ch_color_border = "FFFFFF"; ch_color_text = "000000"; ch_color_bg = "FFFFFF"; The most common error...

Page 1 of 13123Next